insights

Weld overlay vs cladding: bond, process and when to use each

Cladding is the umbrella term for any method that bonds a corrosion- or wear-resistant alloy onto a lower-cost base metal. Weld overlay is one specific cladding route: the alloy is melted onto the substrate by fusion welding, which creates a metallurgical bond, introduces some dilution and works on almost any geometry. Roll bonding and explosion bonding are the other main routes, used mostly for flat plate and the pipe or vessel shells formed from it.

Table of contents:

 

Weld overlay vs cladding: what each term really means

Most of the confusion around weld overlay vs cladding comes from one fact: one term contains the other. Every weld overlay is a form of cladding, but not every clad component has been weld overlaid.

  1. Cladding describes both the goal and the result: a layer of a better-performing alloy permanently bonded to a structural base metal, so the component gets the surface properties of an expensive alloy and the strength and cost of carbon or low-alloy steel. That layer can be produced by fusion welding, by hot roll bonding, by explosion bonding or by other bonding routes.
  2. Weld overlay is the welding route to that result. Filler metal is deposited on the substrate with an arc or beam process (GTAW, GMAW, submerged arc, plasma transferred arc or laser), one bead next to the other and one layer on top of the other. When the deposited alloy is corrosion resistant, specifications often call the same operation weld cladding or CRA (corrosion-resistant alloy) weld overlay. The full sequence, from surface preparation to inspection, is covered in MEGA's guide to the weld overlay process.

Four related terms appear in the same specifications and are worth separating:

  • Weld cladding: cladding produced by weld overlay. In most project documents it is a synonym of corrosion-resistant weld overlay.
  • Hardfacing: a weld overlay selected for wear, abrasion or erosion resistance rather than corrosion, typically with cobalt-chromium alloys (Stellite) or carbide-rich deposits.
  • Buttering: an intermediate weld layer that improves metallurgical compatibility between dissimilar materials before the final weld or overlay.
  • Buildup: weld metal deposited to restore worn dimensions before final surfacing or machining.

A purchase order that only says "clad" is therefore ambiguous. "Clad pipe" usually refers to pipe formed from roll-bonded or explosion-bonded plate, while "clad fittings" or "clad flanges" almost always means weld-overlaid components. The specification, not the word, decides what is being bought.

How each cladding route bonds the alloy to the base metal

The bonding mechanism is the real difference between the routes, because it decides dilution, thickness control, the shapes that can be clad and whether the layer can be repaired.

Weld overlay: fusion bond

The heat source melts the filler metal and a thin skin of the base metal, and the two solidify together. The result is a continuous metallurgical bond along the whole interface. The price of that bond is dilution: some base metal mixes into the first layer and changes its chemistry. Weld overlay is applied to a component that already has its shape, internally or externally, and only on the surfaces that need it.

Roll bonding: diffusion bond under heat and pressure

A corrosion-resistant sheet and a carbon steel slab are assembled and hot rolled together. Temperature and rolling pressure create a metallurgical bond without melting either material, so there is no dilution. The product is clad plate, which is later formed and seam welded into clad pipe or pressure vessel shells. The cladding thickness is fixed at the mill.

Explosion bonding: solid-state impact bond

A controlled detonation drives the cladding plate against the base plate at very high velocity. The impact produces a solid-state metallurgical bond with a characteristic wavy interface, again without melting. Because no fusion is involved, explosion bonding can join metal combinations that cannot be fusion welded, such as titanium or zirconium on steel. Typical products are clad plates, tube sheets and transition joints.

Mechanical lining: the route that is not a metallurgical bond

Lined pipe uses a thin corrosion-resistant liner held inside the carrier pipe by interference fit. The bond is mechanical, not metallurgical, which is why API 5LD treats clad pipe and lined pipe as two distinct products. The pipe ends of lined pipe are typically sealed with a weld overlay, so that girth welds are made between corrosion-resistant surfaces.

Weld overlay vs cladding: side-by-side comparison

The table compares weld overlay with the two main non-welded cladding routes on the attributes that decide a specification.

Bonding mechanism
Weld overlayFusion, metallurgical
Roll-bonded cladDiffusion under heat and pressure, metallurgical
Explosion-bonded cladSolid-state impact, metallurgical
Base metal melted
Weld overlayYes, in a controlled skin
Roll-bonded cladNo
Explosion-bonded cladNo
Dilution
Weld overlayPresent, controlled by process and number of layers
Roll-bonded cladNone
Explosion-bonded cladNone
Stage of fabrication
Weld overlayAfter forming, forging or machining of the component
Roll-bonded cladAt the plate mill, before fabrication
Explosion-bonded cladBefore fabrication
Shapes that can be clad
Weld overlayPipes, fittings, flanges, forgings, bores, sealing faces, asymmetrical parts
Roll-bonded cladFlat plate and shapes formed from it
Explosion-bonded cladFlat plate, tube sheets, transition pieces
Local application
Weld overlayYes, only where needed
Roll-bonded cladNo, full surface
Explosion-bonded cladGenerally full surface
Repair and restoration
Weld overlayYes
Roll-bonded cladNo (damage is repaired by weld overlay)
Explosion-bonded cladNo (damage is repaired by weld overlay)
Typical alloys
Weld overlayNickel alloys (625, 825, C276, C22), stainless steels, Co-Cr alloys, carbide-rich deposits
Roll-bonded cladStainless steels, nickel alloys
Explosion-bonded cladWide range, including reactive metals
Reference standards
Weld overlayASME Section IX (procedure qualification)
Roll-bonded cladASTM A264 / A265 (clad plate), API 5LD (clad pipe)
Explosion-bonded cladASTM A264 / A265 (clad plate)

Dilution and surface chemistry: the trade-off only weld overlay has

Dilution is the one trade-off that exists only in weld overlay, and it is the parameter most specifications are written around. When the arc melts a skin of carbon steel, iron migrates into the first layer of a nickel alloy deposit. Too much iron at the surface reduces the corrosion resistance the alloy was chosen for.

Project specifications therefore set a maximum iron content at a defined depth of the overlay and a minimum overlay thickness after machining. Meeting both drives the choice of process and the number of layers: a second layer deposited on the first is diluted by the first layer, not by the steel, so its surface chemistry is much closer to the filler metal. How this works with the most widely used nickel alloy is detailed in the Inconel 625 weld overlay procedure.

The welding process moves the balance between productivity and dilution. In the deposition rate comparison published in MEGA's Cladding Division catalogue, conventional GTAW sits at the low end and spray GMAW at the high end, with hot-wire GTAW, Polysoude TIGer and controlled GMAW in between. TIGer, the hot-wire TIG process MEGA uses, combines two tungsten electrodes in tandem that merge into a single arc. The single arc exerts lower pressure than classic tandem configurations, so higher currents and travel speeds raise the deposition rate while dilution stays low.

Roll-bonded and explosion-bonded clad avoid the issue entirely: the surface chemistry is that of the wrought cladding sheet. The constraint moves elsewhere, because the cladding thickness is fixed by the plate and any machining or forming has to stay within it.

If your specification sets an iron limit at a given depth, share it with MEGA's engineers at inquiry stage: the process and the number of layers are chosen around that number, not adjusted after the first test.

Choosing the cladding route by component geometry

Geometry narrows the choice before cost does. Clad plate is efficient for large, simple surfaces, while weld overlay follows the part wherever it goes, including changes of direction, branches and sealing faces.

Long straight pipe
Practical cladding routeRoll-bonded clad pipe, lined pipe or weld overlay
WhyPipe formed from clad plate suits long runs in standard sizes; weld overlay covers sizes, wall thicknesses or lengths not available as clad pipe
Elbows, tees, barred tees, wyes
Practical cladding routeWeld overlay
WhyForged or formed shapes with internal changes of direction and branch intersections
Flanges and sealing faces
Practical cladding routeWeld overlay
WhyOverlay applied locally on bore and faces, then machined to final dimensions
Forged components such as buckle arrestors, nozzles and hubs
Practical cladding routeWeld overlay
WhyHeavy forgings cannot be produced from clad plate
Small internal bores
Practical cladding routeWeld overlay with rotating torch head
WhyRequires equipment able to work inside narrow diameters
Asymmetrical parts
Practical cladding routeWeld overlay with stationary workpiece
WhyThe torch moves around the part instead of rotating the part
Worn or damaged surfaces
Practical cladding routeWeld overlay
WhyThe only route that can restore a clad surface in place

These are the cases MEGA's Cladding Division was built for. Horizontal cladding with longitudinal twin TIGer, managed by CNC software, clads the internal and external surfaces of pipes and long products, depositing two layers in a single run of the welding head. Two cameras, one per torch, monitor the weld in real time, and an integrated software-controlled device handles preheating and cooling. MEGA performs weld overlay on pipes up to 12 meters long as well as on forgings, fittings and flanges.

For short bores and irregular parts, vertical cladding with SPXCNC TIGer keeps the workpiece on the ground while an endless rotating head moves the torch, which makes highly asymmetrical products easy to clad. The equipment works on a minimum internal diameter of 38 mm up to 1,000 mm in length, or a minimum internal diameter of 100 mm up to 2,000 mm.

Send the drawings of the fittings and forgings in your line to MEGA's cladding team: you will know which surfaces can be overlaid, in how many layers and with which alloy before the order is placed.

Why clad pipelines still need weld-overlaid fittings

Specifying clad pipe does not remove weld overlay from a project: in a real pipeline the choice is rarely one route or the other. Corrosive flowlines and subsea lines often use clad or lined pipe for the straight runs, but the same line also contains tees, barred tees, piggable wyes, buckle arrestors, flanges and forged hubs. Those components start as forgings or heavy-wall fittings, so their internal surfaces are weld overlaid, usually with an alloy of the same family as the pipe cladding.

The corrosion barrier is only as continuous as its weakest joint. Girth welds between clad pipe and overlaid fittings are made with corrosion-resistant filler metal, and the overlay on the fitting bevels has to match the cladding thickness and chemistry of the pipe it meets. Three points are worth aligning in the specification:

  • the same acceptance criteria for surface chemistry on pipe cladding and fitting overlay;
  • the minimum corrosion-resistant thickness at the weld bevel, after machining;
  • the internal surface finish of piggable components such as wye fittings, where the overlaid bore must allow the passage of pigs.

API 5LD covers the clad or lined pipe; the fittings and forgings are governed by the project specification and the applicable fitting standards, which is where most mismatches appear.

What really drives cost and lead time

There is no universal cheaper option between weld overlay and roll- or explosion-bonded cladding. Both exist to avoid making a whole component from solid corrosion-resistant alloy, and the balance between them depends on a handful of drivers:

  • Surface to be clad: clad plate covers large, simple areas efficiently; weld overlay cost grows with the clad surface and the number of layers.
  • Size: on small diameters, a solid alloy component can cost about the same as a clad one and may be available sooner.
  • Shape: when the part cannot be made from clad plate, weld overlay is the only cladding route, and the comparison becomes overlay versus solid alloy.
  • Layers and process: the dilution limit decides how many layers are needed, and low-dilution, high-deposition processes shorten welding time.
  • Availability: clad plate and clad pipe come from mills in defined dimensions and schedules, while overlay is applied to forgings and fittings produced in-house.
  • Qualification: a weld overlay needs a qualified procedure for the specific alloy and base material combination; existing qualifications shorten the start of production.

How the clad layer is inspected and qualified

A clad layer that is poorly bonded, too thin or off-chemistry defeats the purpose of cladding. Inspection therefore checks exactly those three things, and the usual sequence for a weld-overlaid component includes:

  1. visual and dimensional checks, including overlay thickness after machining;
  2. liquid penetrant testing of the overlay surface for cracks and porosity;
  3. ultrasonic testing of the interface to detect lack of bond;
  4. chemical analysis at the depth defined by the specification, typically for iron content;
  5. macrographic and micrographic examination of qualification samples.

Before production, the welding procedure itself is qualified. ASME Section IX addresses corrosion-resistant weld metal overlay in QW-214, including bend tests and chemical analysis, and hard-facing weld metal overlay in QW-216. Roll-bonded and explosion-bonded plate is inspected at the mill, with bond integrity and cladding thickness checked against ASTM A264 or A265.

MEGA runs these checks within its own quality system. Its in-house laboratory, accredited to ISO/IEC 17025 by Accredia, performs chemical, tensile, impact, micrographic and macrographic tests, and penetrant, ultrasonic and magnetic particle examinations are carried out internally, together with heat treatment and machining. If your project has specific acceptance criteria, ask MEGA's technical team to review the inspection plan together with the quotation.

Advantages and limitations of each method

Weld overlay

  • Works on almost any geometry, internal or external
  • Applied only where needed, after forming or machining
  • Restores worn or damaged surfaces, including on clad plate products
  • Wide choice of corrosion- and wear-resistant alloys
  • Limitations: dilution to control, heat input that affects the base metal, more welding time per square meter than mill-produced plate, qualified procedures required

Roll-bonded and explosion-bonded clad

  • No dilution: surface chemistry of the wrought cladding sheet
  • Uniform cladding thickness over large areas
  • Efficient for flat plate, vessel shells and long runs of standard pipe
  • Explosion bonding joins metals that cannot be fusion welded
  • Limitations: limited to plate-derived shapes, thickness fixed at the mill, no local or post-machining application, repairs still need weld overlay

Weld overlay or cladding: how to specify the right one

Choosing between weld overlay and other cladding routes follows a clear order. Start from the geometry and the stage of fabrication: if the part is a forging, a fitting, a flange or a finished bore, weld overlay is the practical route. Then fix the surface chemistry and thickness requirements, which decide the process and the number of layers. Cost and lead time come last, once the technically valid options are on the table.

MEGA weld overlays pipes, fittings, flanges and forgings with nickel alloys, Co-Cr alloys and stainless steels, with welding, heat treatment, machining and testing under one roof. Send MEGA the drawings, base material, cladding alloy and acceptance criteria of your components: the cladding team will propose the process, the number of layers and the inspection plan.

 

Request catalog